All Collections
Wired Networking
Wired Networking
61 articles
Clicking on Rogue AP Detection on the Controller of the EWS5912FP will not scan or detect wireless signals.
Can EnGenius switches be set up via CLI?
Does the EWS7928P have a “Save” Button on the Maintenance bar of the GUI?
How can I access EGS7228P through the console port?
How can I access EGS7228FP through the console port?
How can I access EGS5212FP through the console port?
How can I access EGS7252FP through the console port?
How can I access EWS5912FP through the console port?
Cannot enable Rogue AP detection on EWS5912FP
There is no “Under Approval” button on EWS5912FP Controller GUI.
Client Isolation is automatically enabled when L2 isolation is enabled on the EWS5912FP Wireless Controller software
What do the Trunk1 to Trunk8 under PVID of my EWS5912FP switch refer to?
I cannot set Captive Portal on 2.4GHz/5GHs SSID profile using Neutron Controller on EWS5912FP.
Does EnGenius switch supports Discovery Protocol to allow IP phones to automatically connect to the voice VLAN (LLDP-MED)?
The EWS5912FP switch was updated to firmware version 1.05.26-c1.6.24. When configuring the SSID profile for managed Neutron APs, Client Isolation automatically enables when L2 isolation is enabled.
On the Controller of the EWS5912FP, there is no option to enable the Captive Portal feature for the main 2.4GHz/5GHz SSID profiles.
Does the EGS7228P support the Cisco Discovery Protocol (CDP)?
A computer is connected to port 5 of an EGS7228P switch. The untagged VLAN has a VLAN ID of 2 but the computer is not getting a valid IP from that VLAN.
Is there a way to set up multiple VLAN profiles at once on the EGS7228P?
What is the Power Budget of my EnGenius Switch?
How many VLAN profiles can be specified on the EGS7228P?
Why can't I ping between 2 computers connected on EGS2110P?
Subnet Mask and CIDR: How many valid hosts can be used on a specific subnet (Classless Addressing)?
Uploading Firmware on an EnGenius Switch
How can we identify if the EGS2110P is a V1 or a V2. What is the difference between V1 and V2? Are there any features on the V2 that is not on the V1?
Which SFP modules are compatible with EnGenius switches?
IPv4 Standard Reserved Addresses
Why does EGS5110P display "0:timeout" when you change the IP?
Should I use fiber or copper for my network ?
Compatible SFP transceiver specifications (Connector type, Wavelength, Fiber type).
How to Fix: Neutron APs status show as “offline” on the Controller.
Why Subnetting is Important
Is there an option to back up the configuration file on the EGS2108P?
What type of cable should be used to connect a computer to an EGS/EWS switch’s serial port?
Is there a length limit to PoE cable runs?
What are the options available on the Neutron Captive Portal?
SNMP support for the EGS2108P, EGS2110P, and EGS5110P
What Serial Software can we use for EGS/EWS Switches?
What trunking Protocol is supported on EnGenius Switches?
How to update Neutron APs managed by a Neutron switch via OCU
How can we identify if the EGS2110P is a V1 or a V2?
What should I do if port 1234 is Closed after doing connectivity test on EZ Master?
What are the settings to be used on the Serial Connection Software (e.g Putty/Hyper Terminal) for Switches?
How can I set up vlan with VID2 as untagged not VID1 on EnGenius Switches?
Can I connect non-PoE devices to the PoE switch's PoE ports?
What ports should be opened for ezMaster to work?
What does "Port Trunking" mean for EnGenius Switches
How to Fix: Error 800 Windows 7 (L2TP over IP Sec Client Unable to Connect)
I can ping my (3) EAP350v2 access points but the EnGenius Zone Controller cannot find them.
Best Practices for EnGenius Managed Network Switches
White Papers: Routers and Network Controllers (3rd party)
White Paper: Using VLANs with EnGenius APs and Switches
My EGS2108P locks up when DHCP lease time is up on the connected DHCP server.
How to open Port on an EnGenius Router
Naming Convention: PoE/PoE+ Switches
Naming Convention: Non-PoE Switches
Installing and setting up VMware Player for eZMaster
Installing and setting up ezMaster on Virtual Machine
I cannot save AP settings changes on the Controller after updating the EWS2910P firmware to v1.05.42_c1.8.55.
ezMaster – Captive Portal Configuration Guide
How to change and add user login on EnGenius EWS Switch?